Call For Free Estimate (650) 560-4646
Gate repair Redwood City

Gate Repair in Redwood City, CA

Stuck open or shut? Call our office and describe what it is doing. That way the tech arrives with the right parts.

  • 4.9 across 150+ reviews
  • CA Lic #1060180
  • Up to 2-year labor warranty
  • Free estimates

We repair swing gates, sliding gates, gate openers, keypads and intercoms for homes, HOAs and businesses across Redwood City, such as Redwood Shores townhomes and the hillside homes west of El Camino Real.

4.9/5
Average across 150+ reviews

Gate repair for Redwood City homes and HOAs

Written by the licensed technicians at Automatic Gate Masters, CA Contractor #1060180. Last updated October 25, 2026.

Gate repair in Redwood City means finding and fixing whatever stops a gate from moving the way it should. Often that is the operator or the control board, but it can also be the photo eyes, a keypad or intercom, or the hinges, rollers and track. Every visit ends with a safety test, so the gate opens, closes and reverses properly.

Redwood City runs from flat bay fill and lagoons to steep wooded hills, so each part of town wears gates out in its own way. One licensed crew handles the motor, the wiring and the metalwork, so you get one visit and one written quote for the whole gate. For a brand-new gate, see our Redwood City gate installation page instead.

Replacing instead of repairing? Zoning Code Section 36.3 caps a solid gate in the front yard at 3 feet, or 5 feet with an open top. A replacement gate has to meet it, even when the old one was taller.

Source: Redwood City Zoning Code, Section 36.3 (Fences). The full list of local gate rules is below.

The first two photos show our Emerald Hills job just west of the city, while the others are nearby San Mateo County projects labeled with their real city.

Common Redwood City gate problems

These six come up again and again on our calls here. Each one traces back to the ground: bay fill, tight lots or steep hills.

Swing leaves with no room on short driveways

Around downtown, Mt. Carmel and Roosevelt, many lots have a short driveway, so a swing leaf can hit a parked car or the garage apron before it opens fully. We can rehang the leaves, cut the swing angle or move the operator, but if that still fails, a sliding gate is the cleaner fix.

Operators straining on steep hillside drives

In Farm Hill, Eagle Hill and up into Emerald Hills, many drives climb hard from the street. On those drives, a swing arm pushes a heavy leaf uphill or holds it back on the way down, so the gearbox wears out early. Before we repair or upsize it, we weigh the leaf against the operator's rating.

Damp control boxes near the Redwood Shores lagoons

The city's General Plan notes high groundwater in many lowland spots, and Redwood Shores sits on low bayfront land inside a levee. Buried wire and control boxes stay damp there, so terminals corrode and the gate starts opening or stopping at random. We dry and reseal the box, replace damaged wire runs and then retest every safety input.

Tracks and posts drifting on bay fill

The General Plan also warns that former tidal flats can settle, most of all where fill meets native soil. When that ground moves, a slide gate track dips or a post leans, so the gate binds or misses its latch. We realign the track, wheels and latch, and we also tell you plainly if a footing needs work.

Leaves and needles blocking photo eyes

On wooded streets in the western hills, oak leaves and redwood needles pile into tracks and coat the photo eye lenses. A dirty or blocked eye makes the gate refuse to close or reverse halfway. Usually a cleaning, a re-aim and a cleared track solve it.

Keypads and call boxes at shared entrances

Townhome associations in Redwood Shores and the office parks near Seaport Boulevard run keypads, card readers, call boxes and barrier arms. When a code or a phone line stops working, we trace the fault from the keypad through the wiring to the operator board.

Call (650) 560-4646

Not sure which one you have? Describe it on the phone instead of guessing, and never force a powered gate or unplug its sensors.

What our repair customers say

4.9 average across 150+ reviews on Google, Yelp and Thumbtack

None of these three Google reviews names Redwood City, but each one is about a Bay Area repair visit, such as a LiftMaster gate or an intercom.

Zoltan DeakLiftMaster gate repair
★★★★★

“Our Liftmaster driveway gate stopped working out of nowhere, which turned out to be a massive headache. The gate would slowly drift open from the wind, I had this whole annoying routine every time I needed to leave the house, and I was constantly stressed about our dog getting out.”

Excerpt from a Google review
Jihan BatresGate intercom repair
★★★★★

“Jack was super professional and respectful of the property. Everything works perfectly now, and I couldn’t be happier with the service. Highly recommend if you need gate or intercom repairs done right!”

Excerpt from a Google review
Ron ShelegGate repair
★★★★★

“Matt from Automatic Gate Masters did an outstanding job repairing our gate. He was prompt, professional, and had everything working like new in no time. Highly recommend!”

Excerpt from a Google review

Redwood City gate and fence rules

Most repairs never touch these rules. However, once a repair turns into a taller, wider or moved gate, Article 36 applies, and shared gates also have fire rules.

Fence and gate heights

  • Front yard: a solid fence or gate in the required front yard (15 feet deep on most R-1 lots) can be 3 feet tall, or 5 feet when the upper part is open (Section 36.3.C.1).
  • Side and rear yards: up to 7 feet, while the front yard stays at 3 or 5 feet (Section 36.3.C.2).
  • Street side of a corner lot: up to 7 feet, set back 18 inches from the sidewalk (Section 36.3.C.3).
  • Next to a home driveway: no solid fence over 3 feet within 10 feet of the driveway, so drivers can see the sidewalk (Section 36.3.B.2).
  • Busy streets and corners: that sight triangle grows to 15 feet at street corners and on listed streets such as Farm Hill Blvd, Alameda de las Pulgas and Edgewood Rd.
  • Arbor over the gate: up to 9 feet tall, 8 feet long and 3 feet deep (Section 36.4.G).
  • Not allowed in residential zones: barbed wire, razor wire and electrified fencing (Section 36.3.B.3).

Source: Redwood City Zoning Code, Article 36. Confirm your own lot with the city, since the posted code can trail recent changes.

HOA and commercial gates: fire access

Because Redwood City and San Carlos share one fire prevention office, the same rules apply in both cities. For shared and commercial gates, it asks for:

  • An approved Knox key box or key switch at vehicle and pedestrian gates, so crews can open them (Knox Standard 100.1).
  • Fire department approval for any gate across a fire access road (California Fire Code 503.6).
  • An emergency way to open the gate that is kept working at all times.
  • Operators listed to UL 325, the safety standard for gate openers, and automatic gates built to ASTM F2200, the gate construction standard.

Sources: Redwood City and San Carlos Fire, Knox Standard 100.1 and California Fire Code Section 503.6. So when we replace an operator on one of these gates, the new setup has to meet them too.

Plain repairs: like-for-like parts such as hinges, wheels, a battery or a board leave the gate unchanged, so no zoning review is involved.

Taller or moved gate inside city limits: talk to Redwood City Planning and the Building Division first. A fence or gate over 7 feet generally needs a building permit, since the California Residential Code only exempts fences up to 7 feet.

Emerald Hills and North Fair Oaks: these areas are unincorporated, so San Mateo County Planning and Building handles them instead of the city.

Neighborhoods we cover

  • Redwood Shores
  • Downtown
  • Mt. Carmel
  • Roosevelt
  • Stambaugh-Heller
  • Centennial
  • Canyon
  • Farm Hill
  • Eagle Hill
  • Edgewood Park
  • Woodside Plaza
  • Friendly Acres
  • Palm Park
  • Redwood Oaks

See a repair up close

These clips come from other Bay Area repair jobs, but the work is the same on Redwood City gates.

Slide gateSlide operator swapA worn slide operator comes out, and then the new one is set and tuned.
Swing gateSwing leaf rehungA dragging leaf is lifted, rehung and set to close level.
Access controlKeypad and intercom wiringA new keypad and intercom are wired to the operator board.

How a Redwood City repair works

Four steps take you from the first call to a working gate, and there are a few safe checks to try while you wait.

Your repair visit

One crew, one quote, one safety test.

  1. 1

    Describe the problem

    Call or send the form, and also tell us your cross streets and the opener brand if you know it.

  2. 2

    Diagnose on site

    The tech checks power, the board, the photo eyes, the open and close limits, and the hinges or track before naming the fix.

  3. 3

    See the price first

    When a part is needed, you get the price in writing, so nothing is ordered until you say yes.

  4. 4

    Repair and prove it

    We run full cycles, set force and limits, and then show you the gate reversing on an obstruction.

Call (650) 560-4646

Safe checks before we arrive

None of these needs tools, but each one saves time on site.

  • Check the breaker and the power switch in the operator box.
  • Wipe both photo eye lenses and clear leaves or bins from the gate path and track.
  • Try a second remote or the keypad, since a weak remote battery is a common cause.
  • Count any beeps or note the code on the board, because it points to the fault.
  • Take a photo of the motor label so the tech can bring matching parts.

Please do not bypass the photo eyes or push a powered gate by hand. To open it by hand, follow our guide to opening an electric gate manually.

For more help by symptom, use the gate won't open or close guide. On LiftMaster boards, the LiftMaster gate repair page lists the error codes.

FAQ

Redwood City gate repair questions

Do I need a permit for gate repair in Redwood City?

Usually not. Hinges, wheels, a battery, a board or new photo eyes leave the gate the same size and in the same place, so the fence rules in Zoning Ordinance Article 36 do not come into play. However, a taller or moved gate, new columns or a new circuit to the operator is different, so we flag that before work starts.

How tall can a replacement front gate be in Redwood City?

In the required front yard, a solid gate or fence can be 3 feet tall, or 5 feet when the upper part is open. In side and rear yards, 7 feet is allowed. Many older front gates are taller than that, so check the rule before you copy the old height.

Does Emerald Hills follow Redwood City rules?

No. Emerald Hills is unincorporated, so San Mateo County zoning and permits apply there instead of the city code, even with a Redwood City mailing address. We check which agency covers the parcel before we quote a new or taller gate.

Do you repair gates at Redwood Shores townhomes and offices?

Yes. We repair shared entry gates, garage gates, keypads and barrier arms for associations and property managers in Redwood Shores. Because the ground there is low and damp, we pay close attention to control box seals and buried wiring.

Our swing gate has no room to open on a short driveway. What can we do?

Sometimes the leaves can be rehung to open outward, or the operator can be set for a shorter swing. If neither works, a sliding gate needs no swing room at all, so it often fits better. We measure the driveway and show you each option before you decide.

Why does our gate open or stop on its own?

Most of the time, moisture or a failing input is to blame rather than the motor itself. For example, a damp control box, a corroded terminal, a stuck vehicle loop or a dirty photo eye can each make the board react without a command. We test each input in turn, so you know which part caused it.

What does a gate repair visit cost in Redwood City?

The price depends on what failed, since each fault needs different parts and time. For example, re-aiming photo eyes or reprogramming remotes is a small job, while a new board or operator costs more. The estimate is free, and you get the written price before any part is ordered.

Do you also install new gates in Redwood City?

Yes. When a gate is past repair, the same crew designs and builds new swing, sliding and cantilever gates. Our Redwood City gate installation page covers styles, openers and the install steps.
Where We Work

Gate repair in Redwood City and across the Peninsula

Although our office is in San Jose, the crew covers Redwood City and the rest of seven Bay Area counties. Pick a county below, or open a nearby city page.

Gate repair near Redwood City

Elsewhere in San Mateo County: San Carlos, Belmont, Foster City, San Mateo, Menlo Park, Atherton, Woodside and Portola Valley. For the full county, see the San Mateo County gate repair page.

View all service areas →

Automatic Gate Masters & Garage Doors · 877 S Winchester Blvd #350, San Jose, CA 95128 · (650) 560-4646

Redwood City gate acting up? Let's get it moving again

Call, or send the symptom and your zip code. Then our office calls back to book the visit, and you see a written quote before any work starts.

Call (650) 560-4646
  • Office hours: Mon to Fri, 7:00 AM to 9:00 PM.
  • Rather text? Message us on WhatsApp (510) 849-7246.
  • Gate stuck right now? Try the safe checks guide first.
  • Licensed and insured: California contractor #1060180, A+ rated with the BBB.
Scroll to Top
Call WhatsApp