Gate Repair and Electric Gates in Santa Clara, CA
Stuck open or shut? Describe the symptom to our office, so the technician arrives with matching parts.
- 4.9 across 150+ reviews
- CA Lic #1060180
- Up to 2-year labor warranty
- Free estimates
We repair swing gates, slide gates, operators, keypads and intercoms for homes, HOAs and businesses across Santa Clara, from the Old Quad and Rivermark to office and R&D campuses. We also build new electric gates.
Get a free estimate · Common local problemsWhile you wait for our call, read the local setback rules or decode a beep pattern.
Photo: our sliding gate project in Los Altos Hills
Gate repair for Santa Clara homes and campuses
By the licensed gate technicians at Automatic Gate Masters, CA Contractor #1060180. Last updated October 25, 2026.
Gate repair in Santa Clara is the work of tracing why a gate will not open, close or reverse correctly, and then fixing that cause. Often the operator or board is at fault, but photo eyes, keypads, hinges, rollers and tracks fail too. We finish every visit by proving the gate stops and reverses, because that is the safety check that matters most.
Santa Clara mixes single-family neighborhoods with large office, R&D and data center campuses. So our work here covers both: home driveway gates and commercial gates that cycle all day. Our office on S Winchester Blvd sits a few minutes from the city line, and one licensed crew covers the motor, the wiring and the metalwork.
Replacing instead of repairing? Santa Clara Zoning Code Section 18.34.050 limits a gate inside a required setback to 4 feet tall. A replacement gate must follow it. Ask Planning before you match an existing taller gate.
Source: Santa Clara City Code, Title 18 (Zoning), Chapter 18.34. More Santa Clara fence rules follow below.
Common Santa Clara gate problems
Here are six common gate problems and how we fix them on Santa Clara homes and campuses.
Gates crowded by short driveways
When a driveway is short, a sliding gate runs close to the street and takes bumps from cars and trash bins. We straighten or replace bent panels and rollers, and then confirm the photo eyes and safety edges still cover the opening.
Related: sliding gate service.
Commercial operators that never rest
Gates at office, R&D, industrial and data center campuses cycle many times more often than a home gate. Because of that load, belts, chains and limit hardware wear out quickly. We rebuild or replace those parts, but when an operator is past its service life, we size a heavy-duty unit for the real traffic.
Related: commercial gates and barrier gate arms.
Street-tree debris on photo eyes
Street trees and yard trees drop leaves and pods into tracks and onto sensors. When an eye is covered, the gate reverses or refuses to close. Usually, cleaning and re-aiming the eyes ends the false trips, although some spots also need a hood or a moved sensor.
Related: gate safety sensor guide.
Posts and tracks on shifting ground
The city's General Plan notes that Santa Clara is almost entirely within a liquefaction hazard zone, and that heavy groundwater pumping once caused subsidence. When the ground under a footing moves, posts lean, latches stop meeting and slide tracks bind. We realign the track, wheels and latch first, then tell you plainly if a footing needs work.
Related: sliding gate service.
Access control out of sync
Keypads, card readers and phone entry units at shared driveways and small commercial lots often outlast their software or their user lists, so codes stop matching. We trace the fault through the reader and the wiring, update or replace the controller, and make sure the gate still fails safe.
Related: telephone entry systems and access control.
Error codes and dead boards
When a board throws a code or goes dark, the fix depends on the brand and the fault. We read the code, test the board and the power supply, and quote a board only when the old one cannot be saved.
Related: beep codes by brand and LiftMaster gate repair.
Unsure which problem fits? Describe it on a call, and leave the sensors connected and the gate unforced.
Gate repair services in Santa Clara
Mechanical, electrical and access faults all get one diagnosis and one quote, so you never need a second contractor. Tap any card for details.
Swing gatesSwing gate repair
We rehang sagging leaves, swap worn hinges and bearings, and straighten bent operator arms.
Sliding & cantileverSliding gate repair
Worn wheels and rollers come off, and then the track is trued and the chain and force are set again.
Gate openersOpener and motor repair
Swing and slide operators, batteries and solar kits get repaired first. A new motor is quoted only when repair no longer pays off.
New gatesNew electric gates
When a gate is past repair, we design and install new swing, sliding and cantilever gates for homes and campuses.
SafetyPhoto eyes and safety edges
Photo eyes and safety edges (pressure strips on the gate) get cleaned, re-aimed or replaced, and then the gate must reverse on an obstruction.
Access controlKeypads, intercoms and loops
Keypads, remotes, vehicle loops (sensors cut into the driveway) and video intercoms are repaired on the same visit.
Regular electric gate maintenance helps a healthy gate stay that way. Outside Santa Clara, see the gate repair hub.
What our repair customers say
4.9 average across 150+ reviews on Google, Yelp and Thumbtack
None of these three Google reviews names Santa Clara. Each one describes a Bay Area visit, such as a motor repair or a new gate.
“My Viking gate motor was acting up for like a week until i had Jack to inspect my gate He had the gate motor up and running super smooth in no time!”
Excerpt from a Google review“Had an issue with my gate, Matt the gate technician was quick to respond! Super professional,knew exactly what he was doing and got everything working perfectly again.”
Excerpt from a Google review“They installed a brand new driveway gate with a liftmaster motor, and everything turned out exactly how I envisioned. Jack was professional, punctual, and really paid attention to the details.”
Excerpt from a Google reviewSanta Clara gate and fence rules
Day-to-day repairs seldom touch these limits. However, a gate that gets taller, wider or moved falls under Chapter 18.34, and shared gates also face fire rules.
Fence and gate heights
- Front setback and corner street side: fences, walls and screens up to 3 feet (Section 18.34.040, Table 3-1).
- Rest of the lot: 6 feet, plus up to 1 foot of lattice. Height is measured from finished grade, and raising the grade to gain height is not allowed (Section 18.34.030).
- Gates, posts and columns in a setback: up to 4 feet tall and 18 inches wide, at least 15 feet from an intersection and outside driveway visibility areas (Section 18.34.050).
- Visibility areas: nothing over 3 feet at street intersections and private driveways. Public Works sets the size of each area (Section 18.30.030).
- Office and industrial zones: security fences of wrought iron, concrete or masonry up to 8 feet, so a campus gate can stand taller than a home gate (Chapter 18.34).
- Not allowed: barbed wire, razor wire, electrified fences and broken glass (Section 18.34.060).
- Architectural Review: new fences need it, unless they meet the rules on R1-6L, R1-8L or R2 parcels (Section 18.34.020).
Source: Santa Clara City Code, Title 18 (Zoning). Ask the city about your parcel, since the published code may not show the newest amendments.
HOA and commercial gates: fire access
Santa Clara amended the state fire code in 2025. For gates across a fire access road, City Code Chapter 15.60 asks for:
- Fire code official approval and an approved way to open the gate in an emergency, kept working at all times.
- Gate openings at least 20 feet wide on commercial sites, or 14 feet for a single-family home.
- Operators listed to UL 325, the safety standard for gate openers, and automatic gates built to ASTM F2200.
- Gates that one person can open by hand, and that are repaired or replaced when defective.
When we replace an operator on one of these gates, the new setup has to meet these rules too.
Sources: Santa Clara City Code, Chapter 15.60 and California Fire Code Section 503.6.
Plain repairs: swapping hinges, wheels, a battery or a board keeps the gate as it was, so zoning review does not apply. However, new wiring to the operator may need an electrical permit.
Taller or moved gate: call the Planning Division at 408-615-2450 first, because a new fence or gate may need Architectural Review. The Building Division (408-615-2420) issues permits for fences over 7 feet. Both sit at City Hall, 1500 Warburton Ave.
Neighborhoods we cover
- Old Quad
- Rivermark
- Westwood
- Forest-Pruneridge
- Lawrence Station
- Bowers/Monroe
- Kimberlin
- San Tomas
- Birdland
- Los Padres
- Montague
- Newhall
See a repair up close
The clips were filmed on other Bay Area jobs, but the same repairs happen on Santa Clara gates.
How a Santa Clara repair works
Four steps lead from your call to a working gate, and the checks on the right can save time while you wait.
Your repair visit
Call, diagnosis, written price, tested repair.
- 1
Share the symptom
Tell us what the gate does, the nearest cross streets and the opener brand, if you know it.
- 2
Diagnose on site
We check power, the board, the photo eyes, the open and close limits and the hinges or track before naming a fix.
- 3
Approve the price
When the fix needs a part, you see the price in writing first. No part is bought without your OK.
- 4
Repair and test
We run full cycles, set force and limits, and the gate has to reverse on an obstruction before we leave.
Safe checks before we arrive
No tools needed, but each check makes the visit shorter.
- Start with the breaker and the power switch in the operator box, since a tripped breaker is an easy fix.
- Wipe both photo eye lenses and clear leaves, pods and bins from the track.
- Try a second remote or the keypad, because a weak remote battery often looks like a dead gate.
- Write down any beep count or board code, since it points to the fault.
- Snap a photo of the motor label, so the tech brings matching parts.
Leave the photo eyes connected, and do not push a powered gate by hand. For a stuck gate, the release steps are in our manual gate opening guide.
Our step-by-step guide for a gate that will not open or close sorts problems by symptom. On LiftMaster boards, the LiftMaster gate repair page lists the error codes.
Santa Clara gate repair questions
Is a permit needed for gate repair in Santa Clara?
Can I put a 6-foot driveway gate at the front of my lot?
Does a new gate need Architectural Review?
Do you repair commercial gates at north side business parks?
Why does my sliding gate stop halfway?
Do you also install new electric gates in Santa Clara?
What does Santa Clara gate repair cost?
How far is your office from Santa Clara?
Gate repair for Santa Clara and the South Bay
Because our office is in West San Jose, Santa Clara is one of the closest cities we serve, and the same crew covers seven Bay Area counties. Pick your county, or jump to a neighboring city.
Gate repair near Santa Clara
Elsewhere in the area: San Jose, Sunnyvale, Cupertino, Campbell, Mountain View, Milpitas, Los Altos and Saratoga. The Santa Clara County gate repair page covers the rest of the county.
Automatic Gate Masters & Garage Doors · 877 S Winchester Blvd #350, San Jose, CA 95128 · (650) 560-4646
Santa Clara gate acting up? Let's get it moving again
Call the office, or use the form with the symptom and your zip code. Then we book the visit, and you get a written quote before work begins.
Call (650) 560-4646- Office hours: Mon to Fri, 7:00 AM to 9:00 PM.
- Rather text? Message us on WhatsApp (510) 849-7246.
- Gate stuck right now? Try the safe checks guide first.
- Licensed and insured: California contractor #1060180, A+ rated with the BBB.








